Samsung SYNCMASTER753DFX Manuel d'utilisateur

SyncMaster 753DFX/753DF

UnpackingFront Rear Bottom 1. Exit buttonUse this button to Exit the active menu or the OSD.2,3. Adjust buttonsThese buttons allow you to highlight a

UnpackingFront Rear Bottom (The configuration at the back of the monitor may vary from product to product.) 1. Power portConnect the power cord for y

UnpackingFront Rear Bottom 1. Signal CableConnect the signal cable to the video port on your computer, video board, video card, or graphics card.2. P

Connecting Your MonitorInstalling the Monitor DriverBase Installation 1. Connect the power cord for your monitor to the power port on the back of the

Connecting Your MonitorInstalling the Monitor DriverBase Installation When prompted by the operating system for the monitor driver, insert the CD-ROM

4. Click the "Install" button in the "Warning" window.5. If you can see following "Message" window, then click the "

Connecting Your MonitorInstalling the Monitor DriverBase Installation Windows XP | Windows 2000 | Windows Me | Windows NT | LinuxWhen prompt

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don&apo

10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating SystemWhen you can see "Digital Signature Not Found" on

Microsoft® Windows® NT Operating System1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Informa

Main > Index Main Page On-Screen DisplaySafety Instructions TroubleshootingNotational Check ListPower Q & AInstallation Self-Test Feature

Connecting Your MonitorInstalling the Monitor DriverBase Installation Tilt/Swivel Base | Attaching and Removing the BaseWith the built-in pedestal,

Attaching the Base1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of

On Screen Display (OSD) Menu System

On Screen Display (OSD) Menu SystemWith the menu off, push the menu button.Push the - button or + button until the Brightnessscreen is display

On Screen Display (OSD) Menu SystemFollow these instructions to change the Position of the monitor’s entire display.With the menu off, push the menu

On Screen Display (OSD) Menu SystemFollow these instructions to change the Size of the monitor’s entire display.Menu How to adjustH-SizeFollow these

On Screen Display (OSD) Menu SystemMenu How to adjustAdjust the pincushion setting when the sides of the displayare bowed in or bowed outPincushionWit

Adjust the rotation setting when the entire displayis tilted left or right.RotationOn Screen Display (OSD) Menu SystemMenu How to adjustAdjust the par

On Screen Display (OSD) Menu SystemMenu How to adjustAdjust the pinbalance setting when the sides of the display arebowed towards the left or right.Pi

On Screen Display (OSD) Menu SystemMenu How to adjustLanguageWith the menu off, push the menu button.Push the - button or + button until the L

Main > Safety Instructions > Notational NotationalPowerInstallationCleanOther Failure to follow directions noted by this symbol could resul

On Screen Display (OSD) Menu SystemA “Moiré” pattern can appear on your screen, looking like aseries of concentric circles or arcs. To eliminate this

On Screen Display (OSD) Menu SystemMenu How to adjustSome video cards use video signals higher than 1.0V whichcauses the display to be very bright. Fo

On Screen Display (OSD) Menu SystemMenu How to adjustFollow these instructions to get a close-up or a longshot viewof the monitor’s viewing area.ZoomW

Note The monitor may buzz momentarily, the image colors maychange and the image will jiggle for a few seconds.These effects are normal.On Screen Displ

On Screen Display (OSD) Menu SystemMenu How to adjustThe information on this screen shows Display Timing , UserTiming and Factory Timing.Display Timin

Main > Troubleshooting > Check List Check ListQ & ASelf-Test Feature Check Before calling for service, check the information in this se

The screen shows strange colors or just black and white.Is the screen displaying only one color as if looking at the screen through a cellophane paper

5.If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel

Main > Troubleshooting > Q & A Check ListQ & ASelf-Test Feature Check Question AnswerHow can I change the frequency? Frequency can

Main > Troubleshooting > Self-Test Feature Check Check ListQ & ASelf-Test Feature Check Self-Test Feature Check | Warning Messages |

Main > Safety Instructions > Power NotationalPowerInstallationCleanOther When not used for extended periods of time, set your PC to DPMS. I

1.If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios,

GeneralPowerSaverPreset Timing Modes GeneralModel NamePicture TubeType 17"(43cm) DynaFlat X (40.6cm viewable)Deflection angle 90 °Dot Pitch 0.20m

GeneralPowerSaverPreset Timing Modes This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your

GeneralPowerSaverPreset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be

GeneralPowerSaverPreset Timing Modes GeneralModel NamePicture TubeType 17"(43cm) DynaFlat X (40.6cm viewable)Deflection angle 90 °Dot Pitch 0.20m

Main > Information > Service ServiceTerms Regulatory Natural Color Authority U.S.A. :Samsung Computer Products Customer Service400 Valley

Samsung Electronics Comercial Iberica, S.A.Ciencies, 55-65 (Poligono Pedrosa) 08908Hospitalet de Llobregat (Barcelona)Tel. : (93) 261 67 00Fax. : (93)

Free Line 800 220 120http://www.samsung.pt/ NETHERLANDS/BELGIUM/LUXEMBOURG :Samsung Electronics Benelux B. V.Fleminglaan 12 2289 CP Rijiswijk, NEDERLA

Information > Terms ServiceTerms Regulatory Natural Color Authority Dot PitchThe image on a monitor is composed of red, green and blue dots.

Main > Information > Regulatory ServiceTerms Regulatory Natural Color Authority FCC Information | IC Compliance Notice | MPR II Compliance

Main > Safety Instructions > Installation NotationalPowerInstallationCleanOther Do not cover the vents on the monitor cabinet. zBad ventila

MPR II ComplianceThis monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.European Notice (Europe only) Prod

environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employ

TCO'99-Ecological requirements for personal computers (TCO applied model only)Congratulations!You have just purchased a TCO'99 approved and

pyThe relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically boun

Main > Information > Natural Color ServiceTerms Regulatory Natural Color Authority Natural Color Software ProgramOne of the recent problem

Main > Information > Authority ServiceTerms Regulatory Natural Color Authority Information in this document is subject to change without n

Main > Safety Instructions > Clean NotationalPowerInstallationCleanOther When cleaning the monitor case or the surface of the CRT, wipe wit

Main > Safety Instructions > Other NotationalPowerInstallationCleanOther Do not remove cover(or back). No user serviceable parts inside. zT

Keep the monitor away from any magnetic substances. zThis may cause discoloring or distortion of the image.

UnpackingFront Rear Bottom Monitor and Stand(Some models include a stand attached. ) Please make sure the following items are included with your mon