Samsung WA13V5 Manuel d'utilisateur télécharger pdf

Fast Track Troubleshooting

Model:

WF520ABP/XAA

WF520ABW/XAA

Publication # tsWF520 Revision Date 02/25/2011

Quick Test Mode

To enter press Spin, Soil, & Power simultane-

ously with the power off.

1. All LED’s light up and the washer beeps as it

enters the Quick Test Mode.

2. After the displaying the software version, LCD

will display Model information. If EEEE is displayed

the PCB ass’y is defective.

4. When the version is displayed, turn the Jog-Dial

CCW so that the version disappears. Press the fol-

lowing keys to test the various components:

Press Temp Key to cycle through the Water Valves

circuit test (lock the door first) in this order: Pre-Wash,

Bleach, Cold Main, Hot, & Steam, then off.

Press Spin Key to test Door Lock/Unlock circuit

Press Steam Level Key to test Circulation/Drain Pump.

Press Soil Key to test the Water/Steam Heater.

When either Test or Spin is displayed on the LCD,

press Start/Pause key to conduct the motor test.

In Test mode, you can test the clockwise and counter-

clockwise movement of the motor. In Spin mode, you

can test the motor at a high rpm.

Service Mode:

This mode allows more detailed operation tests and trouble-

shooting, to enter press Signal & Extra Rinse

simultaneously with the power on.

While in Service Mode the following tests can be performed:

Quick Spin Test = Delay Start & Extra Rinse: This accel-

erates the drum motor from 0 to maximum RPM over a few

minutes. Note: Stay with the washer during this test, out of

balance detection may be bypassed. Press the Start/Pause

button during the test to hold its spinning speed for 10 minutes

before going back to Quick Spin Test Mode. Press and hold the

Delay Start & Extra Rinse button to continue.

Cycle Count = Press Signal button to see # of times used.

Soft Ware # = Press Soil button to see software version info.

Fault Code Test = Press the Spin button to view the stored fault

codes – then turn Jog Dial to view error codes (Push Start/

Pause while the code is displayed to view the number of cycles

since the error occurred, Push Start/Pause to go back to faults)

Peripheral (Main PCB) input Tests

1. Select Extra Wash. Then turn the Jog-Dial so that the Heavy

Duty LED is turned on. Next, press the Start/Pause Key. The

Water Temperature will be displayed in Fahrenheit.

2. Select Extra Wash. Then turn the Jog-Dial so that the Perma-

nent Press LED is turned on. The door status will be displayed

(OP if open, CL if closed).

3. Select Extra Wash. Then turn the Jog-Dial so that the Sani-

tize LED is turned on. The door lock Switch status will be dis-

played (UL if unlocked, Lo if locked).

4. Water Frequency/Water Sensor Testing - Select a cycle &

start the washer, enter Service Mode & press Extra Wash.

Turn the Dial so that the Bedding LED is turned on. Next, press

the Start/Pause Key. The Water Frequency will be displayed.

The frequency will change as the unit fills.

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is

intended for use by persons having electrical, electronic, and mechanical experience

and knowledge at a level generally considered acceptable in the appliance repair trade.

Any attempt to repair a major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

EEPROM Clear Check

Power off, Press Delay Start, Signal and Power Key at

the same time. Good = Good Fail = FAiL

All memory will be cleared, including Fault Codes

This should be done when a new Main PCB is installed

SUPPORT INFORMATION

Training — Plus One http://my.plus1solutions.net/clientPortals/samsung/

Help — GSPN http://service.samsungportal.com/

Samsung Product Support TV http://support-us.samsung.com/spstv/howto.jsp

Customer information videos and chat programs. Programs for Fridges, Laundry, Ranges & D/W

# tsWF520 RevB 02/25/2011

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Model: WF520ABP/XAA WF520ABW/XAA Publication # tsWF520 Revision Date 02/25/2011 Quick Tes

Page 2 - # tsWF520 RevB 02/25/2011

CN8 CN7 CN6 CN10 CN1 CN3 CN6 CN2 RY1 RY11 RY13 To MEMS connector on Main PCB CN11 To MEMS connector on outer tub CN11 PNK BLU YEL RED VIO WH

Page 3

Washer Connector Checks WF520 CN1 1 Door Lock Close (Blk) 2 Door Lock Open (Wht) 3 Drain Pump (Vio) 4 Steam Valve (Brn) 5 Bleach Valve (Pnk) 6 Bubble

Page 4

Door Lock Check Test 1 Test 2 Connector CN6 Pin 2 (Gray) and CN1 Pin 1 (Black) When Door is Locked or Unlocked there is a pulse of 120VAC for a few

Page 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Che

Page 6

Laundry Touch Up Paints TOUCH UP PAINT, BLUE ONYX DH81-11980ATOUCH UP PAINT, IMPERIAL SILVER DH81-11981ATOUCH UP PAINT, NEAT WHITE DH81-11982ATOUCH UP

Page 7 - Main Wash

Pre WashMain WashSoftenerBleachPath #2Path #1Path #3Path #4Path #5V#1 V#2 V#3 V#4 V#5MAIN(H) PRE WASH BLEACH MAIN(C) STEAMWater valve connections for

Commentaires sur ces manuels

Pas de commentaire

Samsung WA13V5 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Machines à laver Samsung WA13V5. Fast Track Troubleshooting Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Samsung WA13V5