Samsung DVD-C550 Manuel d'utilisateur télécharger pdf (Page 4)

Choosing a Connection

Connections

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on

those particular components.

A. Connecting to a TV (SCART)

- Using the SCART, connect the SCART (EXT) terminal on the rear of the DVD Player to the SCART

(IN) terminal of your TV.

B. Connecting to a TV (For Video)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals or 5.1CH

(Front L-R) on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Video signal from the DVD player appears on

the TV screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page.

- The number and position of terminals can vary depending on your TV set. Please refer to the user’s

manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the

DVD player.

- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video

Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN ➝ SCART-RGB ➝ SCART-CVBS)

C. Connection to a TV (Interlace/Progressive)

Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD

player to the COMPONENT IN terminal of TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals or 5.1CH (Front L-R) on the

rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV.

Press the input selector on your TV remote control until the Component signal from the DVD player

appears on the TV screen.

Set the Video Output to I-SCAN/P-SCAN in the Display Setup menu. You can use the VIDEO SEL. button

to change the Video Output mode.

Note

- What is “Progressive Scan”?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

- There is no Component video displayed when "Scart RGB" is selected by pressing video select button

on remote control.

D. Connecting to a TV with DVI/HDMI Jack

Using the HDMI-DVI/HDMI-HDMI cable , connect the HDMI OUT ter-minal on the rear of the DVD player to

the DVI/HDMI IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals or 5.1CH (Front L-R) on the rear

of the DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD player and TV.

Press the input selector on your TV remote control until the DVI/HDMI signal from the DVD player appears

on your TV screen.

HDMI VIDEO Specifications

When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order.

The first press of the HDMI SEL. button brings up the current resolution.

The second press allows you to change the HDMI output resolution.

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user’s manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds.

- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this

DVD player using your TV remote control. This is only available with Samsung TVs that support

Anynet+(HDMI-CEC).

- If your TV has an

logo, then it will Supports the Anynet+ Function.

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission of video and audio data with just a single

connector.Using HDMI, the DVD player transmits a digital video and audio signal and displays a

vivid picture on a TVhaving an HDMI input jack.

• HDMI connection description HDMI connector

- Both uncompressed video data and digital audio data (LPCM or Bit Stream data).- Though the

player uses a HDMI cable, the player outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears

on the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal. However, when playing a DVD, the data trans-

mitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an

analog-to-digital converter (in the TV) is required. During this conver-sion, the picture quality is

degraded due to noise and signal loss. DVI technology is superior because it requires no D/A con-

version and is a pure digital sig-nal from the player to your TV.

1. DVD POWER Button

Turns the power on or off.

DVD Button

Use to select the DVD player for operation.

3. TV Button

Use to select a Samsung TV for operation.

4. EZ VIEW Button

Lets you easily adjust the aspect ratio of a

picture according to the screen size of your

TV (16:9 or 4:3).

MARKER Button

6. REPEAT Button

Allows you to repeat play a title, chapter,

track, or disc.

7. DISC MENU Button

Brings up the Disc menu.

8. INFO Button

Used to displays playback info banner.

9. TV VOL (+, -) Buttons

Controls volume.

10. SKIP Buttons ( / )

Use to skip the title, chapter or track.

11. STOP Button ( )

12. MENU Button

Brings up the DVD player’s menu.

13. ENTER/π/†,√/® Buttons

This button functions as a toggle switch.

14. TOOLS Button

Displays the current disc mode. It also lets

you access the Display function.

15. OPEN/CLOSE ( ) Button

To open and close the disc tray.

16. HDMI SEL. Button

HDMI Output resolution setup.

17. USB Button (Only DVD-C550/

DVD-C550K)

ZOOM Button (Only DVD-C510)

Enlarge the DVD Picture.

18. VIDEO SEL. Button

Changes video output mode.

19.

REPEAT A-B Button

Allows you to repeat play a chosen section

(A-B) on a disc.

20.

SUBTITLE Button

21.

TITLE MENU Button

Brings up the Title menu.

22.

AUDIO/TV SOURCE Button

Use this button to access various audio

functions on a disc.

Use this button to select

an available TV source (mode TV).

23. PAUSE Button ( )

Pauses disc play.

24. SEARCH Buttons ( / )

Allows you to search forward/backward

through a disc.

25. TV CH ( , ) Buttons

Channel selection.

26. PLAY Button ( )

Begins disc play.

27. RETURN Button

Returns to a previous menu.

28. EXIT Button

Exits the on-screen menu.

29.

KARAOKE (

†

) Button

(Only DVD-C550K)

Use to begin Karaoke functions.

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Samsung DVD-C550 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de DVD Samsung DVD-C550